SAFETY DATA SHEET Vitrified Grinding Wheels Safety Data Sheet Vitrified Grinding Wheels 1. IDENTIFICATION Product Identifier: Vitrified Grinding Wheels, Including Surface Grinding Wheels (Type 1) and Mounted Points. Product Use: Abrasive materials used for sanding metals, concrete, masonry, and building materials. Restrictions on Use: Use only as directed.
Always pay attention. Never drift away or allow yourself to get distracted while grinding, as the cup wheel can break if not used properly. For more information on this topic or any other grinding wheel safety information, please review ANSI and OSHA requirements and literature provided by the grinding wheel and machine manufacturer.
It is based on the premise that grinding is a safe operation when a few basic rules are followed. These rules are based on material contained in the American National Standards Institute Safety Requirements B7.1 — "Use, Care & Protection of Abrasive Wheels." Follow them.
General requirements Guarding cup wheels Construction of fabricated guards ... ****means there is a comparable OSHA rule to this paragraph . MIOSHA . OSHA . R 408.10111. Handling and storage of abrasive wheels. ... prevent interference in side grinding and drive the wheel by its clamping force against the depressed portion of the
The Occupational Safety and Health Administration (OSHA) is very specific about bench grinder safety. OSHA refers to bench grinders as "Abrasive Wheel Equipment Grinders." The safety rules for this machinery are in the Code of Federal Regulations (CFR), and OSHA has a very detailed checklist for the bench grinder on ...
ANSI B7.1 has been called the "Bible" for grinding wheel safety for good reason. It is the abrasive (grinding) wheel industry standard for the "Safety Requirements for the Use, Care and Protection of Abrasive Wheels" and most abrasive wheel safety-related questions can be found there.
Store grinding wheels carefully on racks in dry places, and visually inspect them for warping, chips, cracks or other damage before installation. Discard used wheels once they are approximately 2/3 worn. Proper guarding is one of the most important safety requirements. Missing or improperly adjusted guards are common and frequent safety violations.
Safety. WARNING: Grinding & cut-off wheels are EXTREMELY DANGEROUS when USED IMPROPERLY! Comply with ANSI B7.1 safety requirements and OSHA. A copy of ANSI B7.1 safety requirements will be sent to you by Allison Abrasives upon your request.
Remember to document any safety requirements set forth by OSHA as that is the best evidence that safety procedures are being followed. Grinder Safety – Ring-Testing OSHA requires that grinding wheels be ring tested before mounting them. This simple step prevents the inadvertent mounting of a cracked grinding wheel.
OSHA Training Toolbox Talk: Operating a Pedestal or –Bench Grinder Basic Safety Requirements [Reference 1910.215 / 1926.303] Can you believe the surface of an eight-inch diameter grinding wheel that is mounted on a bench
18 · From the Abrasive Wheel standard. 215(a)(2) Do side guards cover the spindle, nut and flange and 75% of the wheel diameter? ... From other OSHA standards. 22(a) Is cleanliness maintained around grinders? ... Are goggles or face shields always worn when grinding? 212(b) Are bench and pedestal grinders permanently mounted?
(1) Grinding machines shall be equipped with safety guards in conformance with the requirements of American National Standards Institute, B7.1-1970, Safety Code for the Use, Care and Protection of Abrasive Wheels, and paragraph (d) of this section.
OSHA 29 CFR 1910.215 specifies that work rests must be kept adjusted closely to the wheel with a maximum opening of 1/8-inch to prevent the workpiece from being jammed between the wheel and the rest. OSHA also states that the distance between the grinding wheel and the adjustable tongue must never exceed 1/4-inch.
The wheel guard enclosure should cover most of the wheel, the spindle, and the wheel mounting hardware. Some of the wheel must be exposed to allow grinding access, but the maximum access space between the horizontal work rest and the top of the wheel guard opening should be no more than 65 degrees of the wheel.
and guarding of grinding wheels and specifies general requirements for grinding machinery and equipment. 1.2 Scope – This standard specifies general requirements for grinding machinery and equipment and incorporates the requirements and objectives of OSHA, ANSI, Air Force and other nationally recognized national consensus
Abrasive wheels used on bench and pedestal grinding machines must be equipped with safety guards. The safety guard encloses most of the wheel — covering the flange, spindle end, and nut projection — while allowing maximum exposure of the wheel periphery.
Safety instructions for cutting-off wheels and grinding discs You have purchased a high-quality product. For your own safety these recommendations should be observed by all users, in the interest of their own safety. Use only tools that comply with the highest safety standards.
Always wear safety glasses, face shield, protective gloves, suitable protective clothing, hard hat, steel toe boots and hearing protection and dust mask if necessary. Keep other employees away while operating power tools. Always use proper guard with grinding wheel, it protects operator from broken wheel fragments.
ANSI B7.1 - The Bible of Grinding Wheel Safety | Norton . ANSI B7.1 has been called the "Bible" for grinding wheel safety for good reason. It is the abrasive (grinding) wheel industry standard for the "Safety Requirements for the Use, Care and Protection of Abrasive Wheels" and most abrasive wheel safety-related questions can be found there.
According to OSHA grinding regulations, grinding machines must have safety guards. A guard must cover the machine's spindle end, flange projections and nut and have secure mounting that keeps it in line with the grinding wheel.
protection, so many people fail to have it that it's the most common OSHA abrasive wheel violation. The second most frequent OSHA abrasive wheel violation also relates to an important protection: work rests. OSHA requires offhand grinding machines to have a rest that can support the piece you're working on.
With respect to changing a grinding wheel on a surface grinder, OSHA says the wheel change takes place outside of the normal production process: i.e., the machine is turned off, grinding operations stop, a guard is removed, and the wheel retainer nut is loosened and removed.
safety concerns, including flying particles and electrical hazards. This procedure outlines requirements in the Occupational Safety & Health Administration's (OSHA) standards regarding abrasive wheels and tools (29 CFR 1926.303). 1. Preparation • Remove flammable materials from the work area. • Ensure work area is clean, free from slip,